product specification date: 08/14/2008 no.61p04029 rev cosmo electronics corporation photocoupler : KPC410 sheet 1 of 7 2 super high speed response photocoupler features 1. 5 pin mini-flat package. 2. super high speed response (t plh ,t phl :typ.45ns at r l =350 ohm). 3. instantaneous common mode rejection voltage(cm h :typ. 500v/us). 4. high isolation voltage between input and output (viso:2500vrms). 5. low input current drive (i fhl : max. 5ma). 6. lsttl and ttl compatible output. applications 1. high speed interfaces for com puter peripherals, microcomputer systems. 2. high speed line receivers. 3. noise reduction. 4. interfaces for data transmission equipment. 5.inverter.
product specification date: 08/14/2008 no. 61p04029 rev cosmo electronics corporation photocoupler : KPC410 sheet 2 of 7 2 1. outside dimension : unit (mm) 0.100.10 2.300.5 0.50 7.000.4 0.40 2.54 4.400.5 3.900.5 date code tolerance : 0.2mm 2. schematic : top view 3 1 5 4 6 1.anode 3.cathode 4.gnd 5.vo 6.vcc
product specification date: 08/14/2008 no. 61p04029 rev cosmo electronics corporation photocoupler : KPC410 sheet 3 of 7 2 absolute maximum ratings (ta=25 ) parameter s y mbol ratin g unit forward current (*1) i f 25 m a peak forward current (*2) i fm 40 m a reverse voltage v r 5 v input power dissipation p d 45 mw supply voltage v cc 7 v high level output voltage v oil 7 v low level output current i ol 50 m a output output collector power dissipation p c 85 mw isolation volta g e 1 minute ( *3 ) v iso 2500 vrms operating temperature t o p r -40 to +85 storage temperature t st g -55 to +125 soldering temperature 10 second t sol 260 electro-optical characteristics ( ta= 0 to+ 85c unless otherwise specified) parameter symbol conditions min. typ. max. unit input forward voltage (*4) v f i f =10ma,ta=25 C 1.6 1.75 v input reverse voltage bv r i r =10ua,ta=25 5 C - v input capacitance c in v f =0, f=1mh z C 60 - pf logic (1) output current i oh v cc =3.3v,v o =5.5v,i f =250ua - 2 250 ua logic (0) output voltage v ol v cc =3.3v,i f =5ma, i ol(sinking) =13ma - 0.4 0.6 v logic (1) supply current i cch v cc =3.3v,if=0ma - 7 15 ma logic (0) supply current i ccl v cc =3.3v,if=10ma - 13 18 ma leak current (*5) i i-o 45%rh,ta=25 ,t=5s,v i-o =3000v dc C - 1.0 ma isolation resistance (input-output) (*5) r i-o v i-o =500v, ta=25 - 10 12 - capacitance (input-output ) (*5) c i-o f=1mhz, ta=25 - 0.6 - pf propagation delay time output (0) ? (1) (*6) t plh - 45 100 ns propagation delay time output (1) ? (0) (*6) t phl i f =7.5ma,v cc =3.3v,rl=350 , c l = 1 5 p f, ta = 2 5 - 45 75 ns output rise-fall time (10 to 90%) tr,tf i f =7.5ma,v cc =3.3v,rl=350 C 30 - ns instantaneous common mode rejection voltage ? output(0)? (*7) cm h i f =0ma, v cm =10v,v o(min) =2.0v rl=350 - 500 - v/us instantaneous common mode rejection voltage ? output(1)? (*7) cm l i f =5ma, v cm =10v,v o(max) =0.8v rl=350 - -500 - v/us
product specification date: 08/14/2008 no. 61p04029 rev cosmo electronics corporation photocoupler : KPC410 sheet 4 of 7 2 note ) typical values are all at vcc = 3.3v, ta= 25c *1 ta=0 to 70c. *2 pulse width <= 1ms *3 40 to 80%rh ac for 1 minute ,f=60hz. *4 at iin =10ma, vf decreases at the rate of 1.6mv/c if the temperature goes up. *5 measured as 2-pin element. connect pins 2 and 3, connect pins 5, 6, 7 and 8. *6 refer to the fig. 1. *7 cmh represents a common mode voltage ignorable rise time ratio that can hold logic (1) state in output. cml represents a common mode voltage ignorable fall time ratio that can hold logic (0) state in output. recommmended operating conditions parameter s y mbol min max unit low level input current i fl 0 250 u a high level input current i fh 7.0 15 m a supply voltage v cc 4.5 5.5 v fanout (ttl load ) n -8 - operating temperature t o pr -40 85 circuit block diagram vcc vo gnd anode
product specification date: 08/14/2008 no. 61p04029 rev cosmo electronics corporation photocoupler : KPC410 sheet 5 of 7 2 fig.1 test circuit for propagation delay time vo 5v pulse input 350 0.1uf c l tplh 3.75ma tphl tf 10% 90% v o tr i f vol 1.5v 5v 0ma 7.5ma fig.2 test circuit for instantaneous common mode rejection voltage sw a v cm b 0.1uf 350 c l vo 5v v o sw:a (if=5ma) vol tf 10% 10% sw:b (if=0) v o v cm tr 90% 90% vo(min) vo(max) 0v 5v 10v
product specification date: 08/14/2008 no. 61p04029 rev cosmo electronics corporation photocoupler : KPC410 sheet 6 of 7 2 fig.2 input diode forward voltage vs. forward current forward voltage v f (v) forward current i f (ma)
product specification date: 08/14/2008 no. 61p04029 rev cosmo electronics corporation photocoupler : KPC410 sheet 7 of 7 2
|
